Aomway TX003 5.8G 64CH 0mw/25mw/100mw/200mw/400/600mw Smart Audio Pitmode FPV Transmitter VTX
Features
Suppourt Smartaudio and Pitmode ,power and frequency can be adjusted by BetaFlight
Suppourt Smartaudio and Pitmode ,power and frequency can be adjusted by BetaFlight
Can be controlled by remote control transmitter
Anti-interference, support more than 8 drones flying at the same time
0mw/25mw/100mw/200mw/400mw/600mw 5 levels power switchable .Output is stable
Long transmission distance and stable signal,≥0.5km@25mW,≥0.8km@100mW. ≥1km@200mW(original antenna)
Stronger power filter can provide the high-quaility real-time image when the drone in full throttle. No snowscreen or any striped image etc..
64CH including 8 race frequencies in the E Band which are used without interference at the same time.
Frequency is locked fast, won't intefere the signal of others
Support NTSC and PAL
Wide voltage, low consumption
2 Working modes, CE mode and normal mode
2 Working modes, CE mode and normal mode
modulate | Wideband FM modulate | ||||||||||
Video Format | NTSC/PAL | ||||||||||
characteristics | Value | Units | characteristics | Value | Units | ||||||
MIN. | Typ. | Max. | MIN. | Typ. | Max. | ||||||
1 |
Output impedance |
50 | ohm | 7 |
Video input level |
0.8 | 1.0 | 1.2 | Vp-p | ||
2 | Output Power | 22 | 23 | 28 | dBm | 8 |
Audio input level |
0.5 | ... | 2.0 | Vp-p |
3 | VCC-IN | 7 | 12 | 24 | V | 9 |
Audio input impedance |
... | 10k | ... | ohm |
4 |
current@12V@ 200mw |
160 | 170 | 180 | mA | 10 | weight | ... | 7.3 | ... | g |
5 |
Video band width |
0 | ... | 8 | Mhz | 11 |
Antenna connecor |
MMCX | |||
6 | Audio | ... | 6.5 | ... | Mhz | 12 | dimensions | 26mm×20mm×8mm |
Operation
Power and frequency can be adjusted by BF firmware. The Pitmode is in 0mW, used for setting in short distance
CE mode& Normal mode. (long press the button for 10s, it will switch between CE and normal mode once.)
In CE mode, the Smart Audio stops working. All CH LEDs flash in blue. Power output locked in 25mW, only 5 channels works : CH1:5725,CH2:5765,
CH3:5800,CH4:5843,CH5:5866MH , and channels only can be switched by button.
Button Control :
Frequency Adjustment : Short prss to change from CH1- CH8
Band Selection : Long press 2s (Fr blue LED flash) into Band Select mode, then short press to change FR(A-H)
Power Switch : Long press 10s(LED shows as follow) into power mode, short press to switch the power from 25mw/100mw/200mw/400/600mw
Indicator | 25mw | 100mw | 200mw | 400mw | 600mw | Defect |
FR | âââ | âââ | â ââ | â ââ | âââ | |
CH | âââ | âââ | â ââ | â ââ | âââ | |
Power |
Flash 1 time Stop 3s |
Flash 2 times Stop 3s |
Flash 3 times Stop 3s |
Flash 4 times Stop 3s |
Flash 5 times Stop 3s |
solid on |
Notice : When use BF OSD to adjust the parameter, be noted that there are only 40CH available in FC, the other frequencies(Band F/G/H) must be adjusted by manual.
Package Inluded
1 x TX003 Transmitter
1 x SMA Antenna Cable
1 x RHCP 4-Leaf Antenna
1 x Molex Pico 1.25mm 6P to 4P AV Cable