Note: The camera for Gopro shown in the photo is not included. Only included camera mount .
Specification:
Brand Name: GEELANG
Mode Name: LIGO78X GOPRO
Item Name: 4S 78mm Ducted Cinewhoop Drone BNF
Wheelbase: 78mm
Size: 119x132x23mmï¼Camera Mount Not Includedï¼
Weight: 90g (Camera Mount Not Included)
Weight: 166g (With 4s 450 Battery, for GOPRO 6 Naked Camera )
Recommended Battery: 4s 450, 4S 550mAh Lithium Battery
FPVï¼CADDX ANT Lite
| Flight controller | Flight controllerï¼SI-F4FC V1 Three-in-one tower Version:MATEKF411 MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Storeï¼Onboard black box Board size:21 * 21MM Power supply: 2-4S battery input (DC 7-17V) Built-in 12A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in Current meter Max 70A Current meter scale set to 480 Built-in 5V 2A BEC Built-in voltage detection |
| Onboard 4in1 ESC | Onboard 4in1 ESC MCU upgraded to EFM8BB21 Power supply: 2-4S LiPo/LiPo HV (7v/17v) Current: 13A continuous peak 15A (5 seconds) Support BLHeliSuite programmable Factory firmware: G_H_30_REV16_77.HEX Default protocol: DSHOT600 |
| Motor | Motor Modeï¼GL1204 KV5000 Stator specificationsï¼D12 * H4 0.2mm for Kawasaki Configu-ration:9N12P Stator Diamter:12mm Stator Length:4mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ16.0mm*15.8mm Magent specifications: N52H Shift specifications: 2mm High strength steel Bearing Specifications: d2*D5*H2.5 MR52zz Japan ISC Custom made WindingSpecifications:180â Class Multipleoxygen-freecopper Weight(g):5.8g No.of Cells(Lipo)ï¼3S-4S |
| 5.8G VTX | Power switching: third gear(25MW ã 100MW ã200MW) Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Raceband Smartaudio ready(Frsky EU-LBT and DSMX version not compatible) |
| Camera | Model: Ant lite Image Sensor: 1/3" CMOS Sensor Horizontal Resolution : 1200 TVL TV System: NTSC and PALswitchable MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm / F2.5 FOV : 165° Min. Illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR : Global WDR DNR |
| Propeller | Gemfan D51 (2020-4) Cinewhoop props Material: PC Weight: 0.91g Pitch: 2 inches Prop diameter: 50.3 mm Center thickness: 4.5mm Center hole diameter: 1.5mm 3 holes |
| Receiver Version (Optional) | Frsky XM+ Non-EU SBUS receiver Frsky AC900 Three-in-one receiver No ground interference (Transmitter and receiver 1 m from the ground): 300m Flysky AFHDS-2A IBUS receiver CRSF Protocol,Official TBS transmitter compatible No ground interference ( Transmitter and receiver 1 m from the ground): 500m DSMX/DSM2 Seria IBUS Receiver Protocol: DSM2/DSMX Compatible Channels: 6-9 (Depend On Your Radio) No Ground Interference (Transmitter and Receiver 1 M from the ground): 300M |
| Battery Recommended | Species : lipoãlipoHV Capacity:450-550mah Voltage:7.8-14.8v Continuous Discharge Rate: 60C Instantaneous discharge rate: 80C Connector: xt30 |
Features:
- Adopt SIF4 1.0 flytower flight controller to support 2-4s lithium battery power supply, independent four-in-one 13a ESC. The integrated Betaflight OSD function keeps abreast of the signal of the flight voltage receiver and can observe the status in real time while flying. With 16m chip black box, it is more convenient to adjust the machine for analysis.
- A more compact design is adopted for the first time, with a wheelbase of 78mm. However, passing long-term flight tests will not affect flight efficiency at all. The FPV end adopts CADDX ANT lite camera, the image quality is clear. The complex environment of flying indoors has better observation and controllability.
- The 4s power supply and 2-inch ducted four-blade propeller have been tested and matched for a long time and have good operability and durability. It is recommended to use 4s 450mah battery, if you need more residence time, you can add 4s550mah battery. Through continuous improvement, the problem of low efficiency of the 2-inch air duct machine was finally solved. Indoor small cross aerial photography becomes a reality. In order to better protect the outer ring, EVA sponge material is used to improve safety and reduce wind resistance. Through some modeling optimizations, the performance is very good.
- Independent use of multiple versions of the receiver, electronic control is more stable. The flight control adopts the newer version of Betaflight 4.2, and the ESC adopts the 16.77 version. Both the two-way DSHOT mode and the gyroscope RPM filter are turned on to make the flight control more stable.
- Using 1204kv5000 motor and 2020 ducted four-blade propeller 3-4s power supply, the efficiency ratio is super high. Flight control stability
- The whole machine is controlled at 90 grams, which solves the weight problem of traditional ducting machines and is flexible in control.
- Package includes gopro6/7 bare metal cover and camera mount, users do not need to purchase separately
- Compared with 3-inch and 2.5-inch air duct machines, the air duct is smaller and the flight efficiency is not affected. By installing the lightweight GOPRO bare metal, it is very suitable for professional video photographers.
Package Included:
1 x 78mm 3D Printing Combined Frame
1 x 3D Printed for GOPRO 67 Naked Camera Caset
Option1: SIF4 1.0 FC external Frsky NON-EU xm+ Receiver
Option2: SIF4 1.0 FC external DSMX receiver
Option3: SIF4 1.0 FC external Frsky AC900 Receiver(Multi-mode receiver)
Option4: SIF4 1.0 FC external TBS NANO Receiver
Option5: SIF4 1.0 FC external FLYSKY Receiver
Option6: SIF4 1.0 FC PNP NO RX Receiver
4 x GL1204 5000KV Motor
1 x 2020 Propeller(4cw+4ccw)
1 x 5.8G VTX5840
1 x RGB LED
1 x GL950 Camera
1 x Screwdriver Removal Tool
1 x Battery Magic Strap
1 x USB 90°Adapter Plug
1 x Caddx Ant Lite
1 x 4s 450mAh Lihv Battery
![DJI Neo - 10 Reasons Buy or [ Not Buy ]. - UCwojJxGQ0SNeVV09mKlnonA](https://i4.ytimg.com/vi/lG4mCfL_Rlw/hqdefault.jpg)
