Holybro Kakute F7 Flight Controller Tekko32 F3 4 In 1 40A Blheli_32 3-6S Brushless ESC Stack 30.5x30.5mm - 100.00 €

Holybro Kakute F7 Flight Controller Tekko32 F3 4 In 1 40A Blheli_32 3-6S Brushless ESC Stack 30.5x30.5mm
Seller: Banggood,
Ship from: CN Warehouse, Usually dispatched in 1-3 work days.

FREE SHIPPING: 10-35 days. (DHL faster please check price/quantity first)
Free shipping aviable, Registered postage from 25 €


Holybro Kakute F7 Flight Controller Tekko32 F3 4 In 1 40A Blheli_32 3-6S Brushless ESC Stack 30.5x30.5mm

Item Specification Feature

Kakute F7

• MCU: STM32F745 32-bit processor
• IMU: ICM20689 (SPI)
• Barometer: BMP280
• Current Sensor: Approximately 130 amps maximum measurable value
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 6 hardware UARTS (UART1,2,3,4,6,7)
• All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
• TF card for Blackbox logging
• Dimensions: 35x41x7mm (includes foam-mounted gy ro board in height)
• Mounting Holes: Standard 30.5mm square to center of holes
• Weight: 9g
• Supports Betaflight, Butterflight, and Cleanflight.
• Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
• Soft-mounting built in. The IMU (“gy ro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
• High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gy ro and accelerometer. Can run at up to 32 kHz sampling rate.
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
• 2 oz. copper PCB allows up to 120A maximum continuous current.
• Dedicated bootloader button for easy firmware flashing.
• Low-pro file design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
• Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
• Supports BLHeli pass-through for easy ESC upgrade and configuration.

Tekko32 F3 4in1 40A ESC

  • 32bit ESC with BLHELI32 firmware

  • Supports 3-6S lipo input

  • PWM input, TLM supported

  • Voltage output (VBAT)

  • NO BEC

  • Supports oneshot / Multishot / Dshot PWM

  • Mounting holes 30.5x30.5mm

  • Supports damped light

  • F3 MCU, runs double faster than F051

  • Extra Cap needed for high current or 6s usage

  • Dimensions: 44x37x6mm

  • Weight: 11.6g


Manual:

http://www.holybro.com/manual/Holybro_Kakute_F7_Manual.pdf


Package Included:
1 x Kakute F7 Flight Controller
1 x Tekko32 F3 4in1 40A ESC
1 x Electrolytic capacito: 1000uF 35v
1 x 8pin to 8pin 1mm pitch 65mm cable
1 x 8pin to 8pin 1mm pitch 25mm cable
















Add Comment





Finger-Clamp Pulse Oximeter Medical Finger Blood Oxygen Saturometro Heart De Oximeter Portable Pulse Oximetro Monitor

Interesting video

Latest views New