iFlight SucceX Mini-W F4 40A 2-6S Flight Tower System (Twin ICM20689) For RC Drone - 87.00 €

The SucceX Min-W F4 TwinG // GY.RO FUSION is the NEXT-GEN flight controller you need for your next build. This FC is ready for anything with 4 UARTS. With its clean intuitive layout, the SucceX Mini-W F4 TwinG makes installation a breeze.

- 8-pin wire connector that allows a simple plug and play connection between your FC and ESC
- 10-pin wire connector for the SucceX 500mW VTX

But the real ma.gic of this flight controller lies in its TWIN GY RO configuration.

The TwinG uses two identical gy.ros oriented side by side with one offset 90 degrees from the other. Betaflight uses GY RO FUSION to blend and average the information from both gy.ros to send a much cleaner signal to the PID loop controller! Less noise and fewer oscillations across the throttle band without adding any delay! Betaflight software filters can be lowered in most cases as well, which brings a significant decrease in delay.

With plenty of processing power and uarts, this is the perfect flight controller for long-ran.ge GPS builds. And the TwinG configuration makes it the perfect Fc for builds like macro quads, cinematic filming rigs and x-class racers that are a bit trickier to tune.

TwinG Gy.ro Setup

-The Betaflight target's default setting is ‘gy.ro_to_use = both’ / Gy.ro fusion is active!

-To check the current setting, please use CLI and type ‘get gy.ro’ to find the responding entry.

-Change the settings with ‘set gy ro_to_use = ’ and type ‘save’.

-To get the most reliable performance or en.counter noise, oscillation and bent props: Please use the default setting ‘both”.

-For Single Gy.ro use, please use the debugging options to find and tune for the cleaner gy.ro, but lose the dynamic fusion and averaging.

-BF offers the following dual gy.ro debug options: dual_gy ro_raw, dual_gy.ro, dual_gy.ro_diff, dual_gy.ro_combined.

-BlackboxLog explorer graph: dual_gy.ro_raw Debugging = [0] Roll Gy.ro1, [1] Pitch Gy.ro1, [2] Roll Gy.ro2, [3] Pitch Gy.ro2.

-The displayed graph will show the Gy.ro_Raw reading (no filters applied), both gy.ros can be compared.

SucceX Mini-W F4 Specifications

-MCU:168MHz STM32F405

-Gy.ro:TwinG ICM20689

-Blackbox: 32MB

-Betaflight OSD: YES

-BEC: 5V 2.5A

-Uarts: 4

-BEC: 5V 2.5A

-ESC Telemetry: RX6

-INA Pad: nuart2

-Input voltage: 2-6S,MAX 8S

-Firmware: betaflight_4.0.5_STM32F405.hex

-CLI dump file: IFLIGHTF4_TWIN_G.config

-Size:27*27mm /20*20mm φ4 mounting

Physical

-Mounting hole: 20*20mm, φ4mm with Grommets φ3mm

-Size: 31*31mm

SucceX Mini-W 40A SPECS:

- MCU: STM32F051K66

- Current Sensor: Yes

- Input: 2-6S lipo

- Telemetry: Yes

- Installing Hole: 20x20mm, M4

- Target: iFlight-BL32-4IN1

- BLHeliSuite download :http://www.mediafire.com/file/hkln8fcaif5s9l8/BLHeliSuite32_32616a.zip/file

- Constant: 40Amps

- Burst: 45Amps

- Weight:16.7g

- Dimensions: 31*31mm(including the power pads)

- Mounting Holes: 20*20mm

- Supports Dshot1200,Proshot,Oneshot,Multishot

5.8G VTX SPECS

-Input voltage: 2-6S

-48 standard channels, A/B/E/F/R Band

-Output Power: pit/20/100/200/500mW

-BEC Output: 5V for Camera or FC

-RF Connector: MMCX

-Video Format: NTSC/PAL

-Size: 26*26mm /20*20mm φ4 mounting

Package Included:

-SucceX Mini-W F4 TwinG FC

-SucceX Mini-W 40A BLHeli_32 4-in-1 ESC

-5.8G 500mW VTX