IRangeX IRX4 Plus 2.4G CC2500 NRF24L01 A7105 CYRF6936 4 IN 1 Multiprotocol STM32 TX Module With Case - 42.00 €

IRangeX IRX4 Plus 2.4G CC2500 NRF24L01 A7105 CYRF6936 4 IN 1 Multiprotocol STM32 TX Module With Case
Seller: Banggood,
Ship from: CN Warehouse, Usually dispatched in 1-3 work days.

FREE SHIPPING: 10-35 days. (DHL faster please check price/quantity first)
Free shipping aviable, Registered postage from 25 €


iRangeX IRX4 Plus 2.4G CC2500 NRF24L01 A7105 CYRF6936 4 IN 1 Multiprotocol STM32 TX Module With Case

Overview:
This 2.4G Multi-protocol TX Module is STM32 ARM microcontroller based module. All available protocols are included in serial mode. It is suitable for many brand of quadcopters, helicopters and airplanes.
This module integrate four RF chips (CC2500,NRF24L01,A7105,CYRF6936) into one single circuit board, it .supports a variety of remote control protocols ,such as for Futaba S-FHSS, Walkera DEVO, Spektrum DSM2, DSMX, Flysky, Frsky, WLToys, Hubsan, Hisky, Esky , Assan etc. You can control your craft flexibility with it , and You will get much excellent experience with you favorite transmitter.

Specification:
Brand Name: iRangeX
Item Name: IRX4 Plus
Operating Voltage: 5-14V
Operating Current: <=100mA
Operating Frequency: 2.4G ISM band
RF Power: +22dBm
MCU: STM32F103CBT6(128K ROM, 20K RAM)
Weight: 45g

Features:
Two operation modes: PPM mode and serial mode.
- When in PPM mode, there are 31 different protocols (protocol NO.0 is reserved for serial mode) mapping to the 16-position protocol selection switch on the module. They are listed in the default protocols table below, when the green light is off, you can use the switch to choose protocol NO. 1 to NO.15, when the green light is on, you can choose protocol NO.16 to NO.31.
- To turn on/off the green light, Please follow these steps:
Turn off you transmitter, point the protocol switch to ‘0’, hold and press the bind button of RF module, then turn on your transmitter, after 3 seconds, release the button.

Normal Use Operation in PPM Mode:
1. Install RF Module in position, Set PPM signal output on you transmitter.
2. According to the default protocols table, turn the arrow sign (the side with a vertical slot) of protocol switch to the proper number to choose protocol.
3. After finish binding operation, Power on your transmitter, the red light of RF module will be on, then RF module is ready to work , after that power on your receiver (or craft).
4. Protocol selection is done at the beginning of power up, so if you want to change protocol during operation, you should recycle the power.
5. The red light will blink slowly if there is no valid PPM signal.

Binding Operation in PPM Mode:
1. Power on your receiver, and set it to binding mode.
2. Hold and press the bind button of RF module, and then turn on your transmitter, after 3 seconds, release the button, you will see the red light flashing rapidly, then RF module is in binding mode, and the red light will go solid after binding.
3. Some protocols (eg: S-FHSS) don’t have binding procedure on RF module, and some protocols (eg: hubsan, e010)will auto bind when power up.

Operation in Serial Mode:
When the green light is off, and the protocol switch is point to ‘0’, you can access serial mode. Transmitter that supports the er9X/erSky9X or Open TX firmware can work in this mode, The model protocol selection and binding is done from the Model Settings menu on the transmitter, For telemetry capable transmitters, the telemetry integration is done seamlessly with the transmitter firmware.
For more information, Please refer to the Link below.
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module
https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md

Notice:
- The jumpers and header attached is used for updating firmware of TX module through USB serial cable. Please remove them for normal use..
- Sometimes, you may need a power recycle when you choose a new protocol. for example, protocol changes from Q303 to HISKY.
- For FRSKY and S-FHSS protocol, you may need set the value of Fine or Option (in the Model Settings menu) properly to bind with your model. The value is varied, since it’s partly depended on your model.

Default Protocols in PPM Mode:

NO. Dial Green light Protocol Sub_protocol Option RF Chip
0 0 Off Serial - - ALL
1 1 Off FLYSKY FLYSKY 0 A7105
2 2 Off AFHDS2A PWM_SBUS 0 A7105
3 3 Off HUBSAN - 0 A7105
4 4 Off FRSKYD - 0 CC2500
5 5 Off FRSKYX CH_8 0 CC2500
6 6 Off S-FHSS - 10 CC2500
7 7 Off DSM2 DSM2_22 7 CYRF6936
8 8 Off DSMX DSMX_22 7 CYRF6936
9 9 Off DEVO - 0 CYRF6936
10 A Off J6PRO - 0 CYRF6936
11 B Off ESKY - 0 NRF24L01+
12 C Off HISKY Hisky 0 NRF24L01+
13 D Off KN WLTOYS 0 NRF24L01+
14 E Off V2X2 V2X2 0 NRF24L01+
15 F Off ASSAN - 0 NRF24L01+
16 0 On MJXQ E010 0 NRF24L01+
17 1 On FRSKYV - 0 CC2500
18 2 On AFHDS2A PPM_IBUS 0 A7105
19 3 On MJXQ X800 0 NRF24L01+
20 4 On YD717 YD717 0 NRF24L01+
21 5 On SYMAX SYMAX 0 NRF24L01+
22 6 On SLT - 0 NRF24L01+
23 7 On CX10 CX10_BLUE 0 NRF24L01+
24 8 On CG023 CX10 0 NRF24L01+
25 9 On BAYANG BAYANG 0 NRF24L01+
26 A On MT99XX MT99 0 NRF24L01+
27 B On SHENQI - 0 NRF24L01+
28 C On FY326 FY326 0 NRF24L01+
29 D On FQ777 - 0 NRF24L01+
30 E On HONTAI HONTAI 0 NRF24L01+
31 F On Q2X2 Q222 0 NRF24L01+


All Available Protocols for Serial Mode:

Protocol Sub_protocol Auto Bind Option RF Chip Reference
FLYSKY   NO 0 A7105 FLYSKY AFHDS
HUBSAN   YES 0 A7105 HUBSAN
AFHDS2A PWM_IBUS NO 0 A7105 FLYSKY AFHDS2A
PPM_IBUS NO 0 A7105
PWM_SBUS NO 0 A7105
PPM_SBUS NO 0 A7105
FRSKYD   NO -10 CC2500 FRSKY D8
FRSKYX CH_16 NO -10 CC2500 FRSKY D16
CH_8 NO -10 CC2500
FRSKYV   NO -10 CC2500  
S-FHSS   NO 10 CC2500 for Futaba
DSM DSM2_22 NO 6 CYRF6936 DSM2,22mS
DSM2_11 NO 6 CYRF6936 DSM2,11mS
DSMX_22 NO 6 CYRF6936 DSMX,22mS
DSMX_11 NO 6 CYRF6936 DSMX,11mS
DEVO   NO 0 CYRF6936 walkera
J6PRO   NO 0 CYRF6936 Nine eagles
HISKY Hisky NO 0 NRF24L01+ Hisky
HK310 NO 0 NRF24L01+  
V2X2 无 NO 0 NRF24L01+  
YD717 YD717 NO 0 NRF24L01+  
SKYWLKR NO 0 NRF24L01+  
SYMAX4 NO 0 NRF24L01+ SYMA
XINXUN NO 0 NRF24L01+ XINXUN
NIHUI NO 0 NRF24L01+ NIHUI
KN WLTOYS NO 0 NRF24L01+ WLTOYS
FEILUN NO 0 NRF24L01+ FEILUN
SYMAX SYMAX NO 0 NRF24L01+ SYMA
SYMAX5C NO 0 NRF24L01+
SLT   NO 0 NRF24L01+  
CX10 CX10_GREEN NO 0 NRF24L01+ CX
CX10_BLUE NO 0 NRF24L01+
DM007 NO 0 NRF24L01+
Q282 NO 0 NRF24L01+
JC3015_1 NO 0 NRF24L01+
JC3015_2 NO 0 NRF24L01+
MK33041 NO 0 NRF24L01+
Q242 NO 0 NRF24L01+
CG023 CG023 NO 0 NRF24L01+  
YD829 NO 0 NRF24L01+  
H8_3D NO 0 NRF24L01+  
BAYANG   NO 0 NRF24L01+  
ESKY   NO 0 NRF24L01+ ESKY
MT99XX MT99 NO 0 NRF24L01+  
H7 NO 0 NRF24L01+  
YZ NO 0 NRF24L01+  
LS NO 0 NRF24L01+  
MJXQ WLH08 NO 0 NRF24L01+ MJX
X600 NO 0 NRF24L01+
X800 NO 0 NRF24L01+
H26D NO 0 NRF24L01+  
E010 YES 0 NRF24L01+ E010/JJRC H36
SHENQI   NO 0 NRF24L01+  
FY326   NO 0 NRF24L01+  
FQ777   NO 0 NRF24L01+  
ASSAN   NO 0 NRF24L01+  
HONTAI FORMAT_HONTAI NO 0 NRF24L01+  
FORMAT_JJRCX1 NO 0 NRF24L01+
FORMAT_X5C1 NO 0 NRF24L01+
FORMAT_FQ777_951 NO 0 NRF24L01+


Differences Between Versions:
Version IRX1 IRX4 IRX4 Plus
A7105 chip
CC2500 chip
NRF24L01 chip
CYRF6936 chip
VCC Power: 3.3V Power supply
Ground Control Distance 200m 240m 240m
PPM
Operating Voltage 5-13V 5-14V 5-14V
Operating Current <=40mA <=100mA <=100mA
perating Frequency: 2.4G ISM band
RF Power: 22dBm
Firmware: STM32F103C8T6
Dimension: 49x22x65mm
Weight 43g 40g 45g
Antenna Length: About 108mm

Model - Protocol Table, Click Here

Firmware for JR 9XII, Click Here

Package Included:
1x iRangeX IRX4 Plus TX Module


,
,
,
,
,

Add Comment





Finger-Clamp Pulse Oximeter Medical Finger Blood Oxygen Saturometro Heart De Oximeter Portable Pulse Oximetro Monitor

Interesting video

Latest views New