Techninės specifikacijos
Basic Information
Weight
7.2g
Price
51.26 €
Integrated Circuits
Barometer
Built-in
Specifications
Firmware
BLHeli_S J-H-40
Blackbox
8MB Onboard Flash
Dimension
35 * 35 * 5.5mm
Product Name
SpeedyBee F405 Mini BLS 35A 20x20 Stack
Flight Controller
SpeedyBee F405 Mini
ESC
SpeedyBee BLS 35A Mini V2 4-in-1 ESC
Bluetooth
Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
WiFi
Not supported
Wireless FC Firmware Flashing
NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update
Wireless Blackbox Dwonload & Analysis
NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis.
Power Input
3-6S LiPo
Mounting
20 x 20mm ∅3.5mm hole sizeï¼compatible with M2 and M3 screws/Silicone grommets.
MCU
STM32F405
IMU(Gyro)
ICM42688P
USB Port Type
Type-C
OSD Chip
AT7456E chip
BLE Bluetooth
Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.
DJI Air Unit Connection Way
Direct soldering
DJI Air Unit Compatibility
Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on th
BetaFlight Camera Control Pad
Yes(CC pad on the front side)
Current Sensor Input
Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.
5V Output
4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.
9V Output
1 group of 9V output, one +9V pad on front side. The total current load is 3A.
3.3V Output
Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.
4.5V Output
Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal
M1 - M4 wires or soldering pads on bottom side.
UART
6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry
Not supported
I2C
Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc
Traditional Betaflight LED Pad
Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.
Buzzer
BZ+ and BZ- pad used for 5V Buzzer
BOOT Button
Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
RSSI Input
Not Supported
Smart Port / F.Port
Not Supported
Supported Flight Controller Firmware
BetaFlight(Default)
Firmware Target Name
SPEEDYBEEF405MINI
Continuous Current
35A * 4
Burst Current
45A(5seconds)
ESC Protocol
DSHOT300/600
Power Output
VBAT(Battery voltage, used to power the flight controller)
Current Sensor
Support (Scale=250 Offset=-500)
