This is the new TAU-H5 from IFLIGHT RC, coupled with the NOX v2.17 Powered by ION 2207 1660kv motors.
The motor, prop, esc combo made this craft very smooth with lots of pop and tourqe! 1185g thrust on a 4s!
In this video i go through how to setup, build, and fly! Screenshots of pids, and rates in the video as well!
The build went together as easy as always due to included instructional layout, and the simple disign of this racing/freestyle frame.
all frame pieces interlock, and all held together with only 4 posts! The carbon Parts where all cut with perfection in mind, from the rounded edges to the slide locks on the supports!every piece was crafted
with the engineer in mind!
As we all know, the faster you go, the more likely you will break an arm, but no worries because the easy interlocking replacable arms are found on iflights website, and
thier customer service reps are always ready to help with any replacement parts or technical support!
The NOX v2.17 came preflashed with Betaflight and a soft serial to allow telemetry to be delivered from the 35a 4n1 blheli-s esc to relay voltage and amperage back to the f4 fc running the its own NOX firmware. All ports are pre set accordingly. i did however rotate the fc orientation 90 degrees to have the motors allign to motors 3 and 1 in rear and motors 4 and 2 up front.
I did that on the config page in betaflight, wicked easy, no remapping of motors needed! After setting up my Rx and modes, I went out for a rip!
Yes it is a DVR vid! sorry. but show me the propwash!
Any questions feel free to ask! Any comments, feel free to post!
I hope you enjoy!
full parts list and specs:
http://www.iflight-rc.com/tau-h5-5inch-212mm-fpv-racing-frame-kit.html
http://www.iflight-rc.com/poseidon-all-in-one-aio-v2-f4-flight-controller.html
http://www.iflight-rc.com/iflight-nazgul-t5061-5-inch-3-blade-pc-material-propeller-cw-ccw.html
http://www.iflight-rc.com/iflight-ion-drive-2207-2500kv-brushless-motor-fpv-racer-drone.html
http://www.nidici.com/
https://www.amazon.com/Antenna-Transmitter-Receiver-Fatshark-Goggles/dp/B07951P6FT/ref=sr_1_1_sspa?s=toys-and-games&ie=UTF8&qid=1525018737&sr=1-1-spons&keywords=stubby+fpv+antenna&psc=1
gear specs
The iFlight Poseidon V2 All In One Flight Controller
Support 2-4S, comes with 5V 1A BEC output.Support SBUS, IBUS, DSMX,SUMD receiver.
Receiver configuration is UART-RX.
- All in one that is really an all in one
- F4 STM32F411 Processor
- ICM20608 Sensor
- 4 x 35A Blheli_s Esc's Dshot 1200 Capable
- Omnibus OSD - Betaflight drag and drop programming
- Direct connect 2-4S with filtered Output of 5v 1.5A
SPECS:
- Dimension:48 x 36mm
- Mounting holes: 20 x 20mm
- Target: Betaflight-NOX
- Firmware:Latest Betaflight / NOX
- Weight:21.1g
Features:
- SPI Gyro ICM20608
- On-Board OSD (controllered by Betaflight, FC over SPI bus)
- F4 Processor (F405)
- 5v1a SBEC
- Built-in Current Sensor
- 4x 35A BLHELI_S ESCs (DSHOT Ready)
- 2x UART
- Buzzer output
- WS2812B LED output
ION SERIES MOTORS
Features
-7075 milled aluminium Bell and Base
-NMB Japan 4mm bearings
-High temperature magnets and windings
-N52H Arc Magnets
-Hex bolt shaft set screw
-Dynamically balanced
-Single strand wounded,
Specifications
2207 1660kv
KV: 1660
Configuration: 12N14P
Shaft Diameter: 4mm
AWG: 18#
Internal Resistance: 46mO
Motor Dimensions (Dia.*Len): F27.7×17.3mm
Weight with wires(g): 37.2g
ldle current@10v(A): 1.4A
No.of Cells(Lipo): 3-4S
Max Continuous Power 180s: 424W
Max Continuous Current 180s: 24.6A
Cable length: 150mm
iFlight T5061 props throw an amazing 1185g @ 19.5a!
FRAME
iFlight Team Edition TAU-H5 5inch 212mm FPV Racing Frame Kit
Features:
- High quality 3K full carbon
- Solid 3mm thickness Bottom frame plate
- 5mm removable arms
- 3D print TPU micro camera, Gopro & antenna mount
Specifications:
- Chamfred Edge/ Coated carbon plate
- Product name: TAU-H5
- Wheelbase:212mm
- Bottom plate thickness:3mm
- Top plate thickness:2mm
- Arm thickness:5mm
- Vertical Side Moun thickness:2mm
- Motor mounting hole size: 16*19mm
- Weight:66g/88.8g (with or without side vertical mount & 3D print TPU Gopro mount )
http://www.iflight-rc.com/
